1. Remove the battery cover on the back of your URC.

2. Observe the polarity of the batteries and the "+/-" marks inside the battery compartment.

3. Insert the batteries.

4. Push the battery cover back in place

Important note on changing batteriesWhen all batteries are disconnected, the URC retains its setting only for 15 minutes. Should you fail to replace new batteries in time, or if weak or bad batteries had been left in the remote for an extended period of time, the URC may need to b reset. Use stylus or pen to reset the unit. The reset button is located inside the battery compartment.Note: You may need to set up your URC again after resetting the unit.

HOW TO SET UP THE URC
There are 4 Device Modes ("TV", "VCR", "CTV" & "AUX") in your URC. You may set up the URC by the following code entering or searching instructions.

[1]Set Up by Entering Device Code

Referring to the DEVICE CODE LIST, look up the 3-digit Device Code which corresponds to the brands and models of your A/V equipment. If there are more than one Device Code listed under your brand, try from the first code with the following instructions:

For example, entering your TV's code:-
1. Hold down "ENT" and "RCL" together simultaneously for 4 seconds until the indicator lights up.

2. Press a desired Device Mode Key (e.g. "TV").

3. Use the number keys to enter your 3-digit Device Code. The indicator should go out immediately.

Turn on your device (e.g. TV), try the function keys on the URC. If your device (e.g. TV) responds to your invoked function correctly, you have entered the right Device Code

Otherwise, repeat the above set up instructions with the rest available Device Codes until your device (e.g. TV) responds to your invoked function, and most keys work correctly.

Simply repeat the above procedures to enter the Device Codes for your VCR & CTV. (Remember to press a correct Device Mode Key in step 2 above)

Note : - Any Device Codes can be entered into "CTV" & "AUX" modes. Just simply press "CTV" or "AUX" Device Mode key in step 2 above and enter your 3-digit Device Code for CTV or other devices. If the indicator flashes twice during the above procedures, a wrong Device Code has been entered. You are required to repeat step 2 to 3 again.

Suggestion: - If you cannot find a correct Device Code for your equipment, see Set Up by SEARCHING THROUGH THE LIBRARY section. - You are recommended to write down your Device Codes on the space provided at the back label after setting up the URC correctly for future reference.

[2]Set Up by Searching through the Library
If you cannot identify a correct Device Code for your equipment from the Device Code List, you may try our code search method:

For example: Turn on your device (e.g. TV).
1. Hold down "ENT" and "RCL" together simultaneously for 4 seconds until the indicator lights up.

2. Press a desired Device Mode Key (e.g. "TV").

3. Enter a following corresponding Magic Search Code, and your URC is now ready to start searching.

DEVICE TYPE TV VCR CTV

MAGIC SEARCH CODE 990 992 994

(e.g. "ENT" & "RCL" ... "TV" ... 990)

4. To search :
Aim your URC at the device (e.g. TV), press the "PWR" and "VOL+" key alternately, repeatedly, slowly and patiently until the device has been turned off.

Once your device has been turned off, immediately press the same device mode key (e.g. TV) again to lock in code and the indicator should go out.

Simply repeat the above procedures to search the Device Codes for your VCR and CTV. (Remember to press a correct Device Mode Key in step 2 above)

Note - TV, VCR and CTV's Device Codes can be searched and locked into "CTV" & "AUX" modes. Just simply press "CTV" or "AUX" Device Mode key in step 2 and enter an appropriate Magic Search Code to start searching - Each time you press the "VOL+" button, the URC will skip to the next code. Then press the "PWR" button to send out a POWER signal trying to turn off your device. If you failed to stop pressing "VOL+" in time when your device has been turned off, turn on your device again immediately. Before the indicator goes out, press "VOL-" on the URC to skip backward. Repeat the step 4 above and lock in code. - If the indicator flashes twice after your pressing of "VOL+" key, you are already at the last code of the library. You may press "VOL-" to search backward and repeat carefully the above procedures to search again. - If the power on/off function of your device is not infra-red controlled - you need to follow steps 1 to 3 above and start searching: - Press "VOL+" and another important function key alternately until your device responses to the expected function, press the same device mode key again to lock in code. e.g. Press "VOL+" & "1" alternately, or; Press "VOL+" & "PLAY" alternately until the device responds.

OPERATING THE URC

Normal Operation
Once you have set up the URC for your A/V equipment, it works like your original remote controls. To operate, just aim it at your equipment, press an appropriate device mode key and then invoke the desired function by pressing a corresponding key on the URC. The indicator flashes during signal transmission and as confirmation of key touch.

Certain function key may not perform or may perform other special functions depending on the DEVICE CODE entered. Trying all keys and functions of the URC is the best way to determine their particular function on your devices.

Punch Through
Punch through allows you to operate TV and VCR function without having to select the device modes repeatedly. You may control TV's volume and mute even you are in VCR or CTV mode; and you may control VCR's tape management function even you are in TV or CTV mode. These buttons work independently with the Device Operating Mode.

MAINTENANCE
1. Do not expose your URC to dust, strong sun light, humidity, high temperature, or mechanical shock.

2. Do not use old and new batteries together as old batteries tend to leak.

3. Do not use corrosive or abrasive cleansers on your URC.

4. Keep the unit dust free by wiping it with a soft, dry cloth.

5. Do not disassemble your URC, it contains no user-serviceable parts.

TROUBLESHOOTING
Q. My URC does not work at all!

A. Check your A/V device, if the device's main switch is turned off, your URC could not operate your device.

A. Check whether your batteries are inserted properly and are in correct +/- marks.

A. If the batteries are low, replace the batteries, See "HOW TO INSERT BATTERIES".

Q If several Device Codes listed under the brand of my A/V device, how can I select the correct Device Code?

A. To seek the correct Device Code for your A/V device, test the code one by one until most keys work properly.

Q. My A/V equipment responds only to some of the commands.

A. You have set a code for which only some commands work properly but some do not. Try other codes until most keys work properly.

Q. May I set up the URC to control more than TV, VCR and CTV at a time?

A. The URC can control more than one device of the same type at a time by programming the device code in the CTV & AUX device mode. Please see SET UP the URC section.